Why is My Diesel Truck Blowing Smoke Out of the Tailpipe?

Diesel Truck Blowing Smoke

Maintenance and care for our vehicles is important to keep them riding for many years. Even though we try, we can’t control everything, so in this article, Callahan Auto & Diesel will assess and address what is happening when smoke is blowing out of our diesel truck tailpipe.

To assess the symptom, we need to know if it’s white, black or blue smoke. This will be obvious to the eye but each is caused by a different issue.

White Smoke

If it’s white smoke, it means that the diesel fuel is not burning correctly. (Be careful as the unburnt diesel has many toxins that can sting the eyes.) This is probably due to lack of heat in the combustion part of the engine and likely caused by one of the following:

  • Injector timing is incorrect
  • Clogged fuel filter
  • Water in diesel
  • Worn seals in the engine

To address the problem, you can siphon out the diesel and replace with new diesel and determine if there was water in the diesel. If that doesn’t work, you can change the fuel filter. If it’s not one of these issues, you’ll probably need to take to the car mechanic to check the fuel injectors or engine seals.

Black Smoke

Black smoke means there isn’t enough oxygen mixing with the diesel, so some of the diesel is not burning and being emitted as black soot.

This is likely caused by:

  • Damaged injectors or injector pump
  • Clogged or gummy cylinder head valves
  • Dirty air cleaner

You can address the injector, injector pump, or air cleaner with replacements and if the head valves just need a cleaning. Replacing the head valves will likely need a visit to the local mechanic.

Blue Smoke

If there is blue smoke, it’s usually caused by too much lubricating oil in the engine during combustion and when burnt, it emits as a blue smoke.

This symptom can be used by:

  • Leaking or worn valve stem or turbocharger seals
  • Incorrect type of oil used
  • Excess engine oil in sump
  • Old or worn out engine

Most of these are signs of an aging vehicle and are relatively common; a tune up can help to clear up the blue smoke issue with new seals and other engine parts that degrade over time.

What Does Timing Belt Service Include?

Timing Belt Service

Next time your mechanic tells you that your car’s timing belt needs a replacement and may cost a thousand dollars or more, do not panic. Do not assume that the guy is trying to rip you off.

The timing belt is one of the most crucial parts of your car’s engine. If it fails, so will your engine, leaving your car in the shutdown mode for good. So it is essential to replace it periodically.

You are better off replacing it then and there instead of having it broken on the highway when you are driving at 80 miles per hour. It’s a definite safety issue.

What does the timing belt do?

The timing belt is an integral part of most combustion engines and synchronizes the rotation of the camshaft and the crankshaft. It causes the valves in the engine open and close at the right times so that the air and fuel flow through the engine.

The valves are opened when the piston sucks the air and fuel inside the chamber. This is called the suction/intake stroke.

The valves are then closed and piston gets the chance to compress the fuel and air (also known as charge). This is the compression stroke.

For gasoline cars, a spark plug ignites the compressed charge creating the explosion and giving the piston its power to push down. The valves are still closed. This is known as the power stroke.

After the power stroke is completed, the valves are opened. The piston again comes up exhausting the burnt charge out of the combustion chamber. This is the exhaust stroke.

The timing belt ensures that the opening and closing of the valves in the combustion chamber take place at the right time and in sync with the camshaft, and the crankshaft; basically the strokes of the engine.

When to replace the timing belt?

Unfortunately, there aren’t clear signs given by the timing belt before its demise. It will just snap off. That’s why most automobile companies suggest that the timing belt should be changed every 60,000 to 90,000 miles. Your car’s manual will provide the exact number for your model.

What is included in my timing belt service?

The process of servicing/replacing the timing belt is very tedious and requires the mechanic to first disconnect the battery ground cable. Once the engine cools down, the crankshaft is set to the top dead center with the first piston being on the compression stroke. Then the crankshaft pulley is carefully removed. All accessories that come in the way of the mechanic and the timing belt are removed. Camshafts are locked and the position of camshaft timings are marked. After removing the idler pulleys and belt tensioner, the timing belt is carefully removed.

Installing a new timing belt is basically the same process in reverse. The mechanic ensures that after the installation, the camshaft and the crankshaft are in perfect alignment. Then the engine crankshaft is turned two full rotations by hand, and the timings marks on camshaft and crankshaft are confirmed.

Your final bill may seem slightly heavier if a broken timing belt has damaged other parts of the engine such as valves, piston, or water pump.

How To Replace Brake Pads

Changing of brake pads is a simple task that anyone can do at home. If you learn to replace your brakes, then you will be able to save a lot regarding maintenance costs.  Automotive Super Center we are always here to serve you but as a vehicle owner, you may want to learn how to replace brake pads at home. Some of the tools you need include:

  • A new set of brake pads
  • Floor jack to lift the vehicle
  • Safety stands to support the car
  • User’s manual
  • Assorted sockets
  • Rackets
  • WD 40
  • Wire brush
  • Gloves

How To Replace Brake Pads.

  1. Park your vehicle on a flat area and ensure your car is in neutral. Chock the wheels that you are not working on to minimize movement. You will then need to loosen your vehicles wheel nuts first. You can choose to loosen the front or the rear wheels. Once you loosen the wheel nuts, you will be able to jack your vehicle up. Ensure that the jack is placed on the right point on your vehicle’s chassis. You can refer to your user’s manual for clarity.
  2. Place the safety stands under the vehicle. You can then remove the wheels after the car is well mounted on the safety stands. The brake caliper would then be visible after you pull out the wheel. You can use the wire brush to remove any dirt on the caliper before applying the WD-40. This will assist in making the removal of the bolts to be fast and efficient.
  3. Inspect the caliper to see the amount of pressure exerted by the hydraulic fluid on the pads. You may unbolt the nuts holding it down. Pull the caliper out and hang it on the wheel well.
  4. Check how the brake pad is installed on the vehicle. The pads have clips which hold them on to the brake assembly. You can now remove the worn out brake pads with ease. Inspect the brake pads for wear and warpage. If the rotor is worn out, you can resurface it or replace it.
  5. You can now install the new brake pads. Ensure they fit in the same position as the old ones. Apply anti-seizure lubricant on the metal contacts to prevent squeaking. The oil should not touch on the brake pads, and it would reduce the braking effect.
  6. Inspect the brake fluid level and ensure its at the right level. You can now replace your caliper on to the wheel assembly. Tighten the bolts holding the caliper using the appropriate socket and ratchet. Place the wheel back on and tighten the wheel nuts using your hands.
  7. Lower the vehicle then tighten the nuts in a zigzag pattern. You can now start your car to test the new brakes. Pump the brakes severally to ensure they seat well in their position. You may then top up your fluid level and perform a road test.

How To Repair A Blown Head Gasket In An Audi

Every one of us dreams to buy a car one day. We strive and work hard for it. Having a car is a great feeling and once you buy it with your own hard earned money, you realize the fact that it is really important to maintain your car and keep it safe. Here at Palumbo’s Automotive, we know that repairing a car can be  costly and we want to help.

The maintenance of an Audi is a really expensive task. And talking about expensive, if you have blown your head gasket in your Audi then surely the repairing coat will be very high. But if you follow a few simple steps then surely you yourself can repair it. Hence here How to repair a blown head gasket in an Audi will be explained.

Firstly disconnect the negative battery terminal located at the top of your battery. Safety should be maintained at all times. Then carefully remove the intake hose and the airbox. Now after this you will have to remove several bolts. You will have to take off the air conditioner compressor. Then you will have to disconnect the water hose by loosening the clamp. Then after this simply remove the bolts of the alternator. Then the lines running to the AC should be disconnected.

Then the next step should be done with care. Loosen the head bolts of the head gasket in place. Then carefully the cylinder head should be cleaned. This has to be done so that the new head gasket sits correctly. After placing the new head gasket in the specified space, tighten the bolts. Then quickly and carefully replace all the components.

Finally, fill the cooling system with fresh coolant. Then after this turn on the engine. Then finally once it reaches its optimal temperature, your car will be ready to use again. This is how to repair a blown head gasket in an Audi.

Here is how it is done.

4 Causes That Can Lead to Head Gasket Failure in a Mercedes

Head Gasket Failure in a Mercedes

Head gasket failure in your Mercedes is surely bad news; and the biggest concern is, you must take care of it immediately. There are a number of different ways a head gasket can fail – from loss of compression to oil and coolant leaks. But before you learn How to repair the head gasket on a Mercedes, you must know what exactly leads to head gasket failure.

A Mercedes head gasket can fail due to many reasons. http://bavarianmastercare.com/ suggests 4 reasons to look our for:

Overheating

An overheating engine can be one of the biggest reasons for a head gasket failure. Most of the times, the gasket’s armor over the cylinders can be crushed and when that happens, the seal around the armor is lost. That time, the engine of your car loses its compression, leading to leaked coolant causing the gasket to erode.

Error in installation

If you already have replaced a head gasket on your car and you have installed it incorrectly, then it can lead to a head gasket failure too. You need to ensure that the head bolts are properly tightened in a correct sequence and properly set to the torque. Make sure that they have clean and undamaged threads. The head surface of the cylinder along with the engine block should also be flat, clean and smooth.

Hot Spots

A lot of engines are vulnerable to hot spots and these can be seen between the cylinders in the center. This can lead to head gasket failure in the near future. If your car is old enough and you have replaced your previous gasket with another one, then hot spots can be a prime reason for your car’s gasket failure.

Poorly design head Gasket

Many times, the car’s head gasket is poorly designed and that can be a reason for a blown gasket in the coming years. So, before you purchase a vehicle, it is important that you do a little research on your gasket, whether or not it is properly designed. If you see problems with the design of your car’s original head gasket, then you must install a better one.

Best Cars To Drive In San Francisco

Best cars to drive in san franciscoDriving in San Francisco requires you select the best type of a car in terms the size as well as the strength of the car putting the terrain, the busy one-way street roads and the dense population in the city area. San Francisco is a hilly city with lots of cars. https://www.mysfcarguys.com/ suggests you consider these as some of the best cars to drive in this city;

Jeep Grand Cherokee

The Jeep models have a good name when it comes to a variety of terrains. The car performs really well in mountainous and hill climbing. It also has perfect edge cutting features that will assist it to survive in San Francisco busy traffic. The spare parts are readily available, and the fuel consumption is average.

Mercedes-Benz-E-Class

This car is just the perfect one when it comes to the traffic nature of San Francisco. It has very a very good and responsive cruise control that brings it into a halt to allow the car in front to move. The car can steer itself at a speed of 40km/h without your hands on the steer. It is also strong for the hilly terrain. Since the vehicle is strong, the hilly areas do not challenge it and remain intact after a steep hill.

Ram 2500

The size of this car allows you to maneuver through a busy road. It also gives you a clear sight to avoid accidents on the busy streets of the city. The power of the car’s engine makes driving in hilly terrain a simple experience making the journey through San Francisco easy.

2018 Volkswagen GTI

This car has a relatively small body that allows you to survive on the busiest San Francisco street roads. The car is compact with a hatchback. The best thing is that it really fits a classy city car with some power to climb hilly places as well.

These are just some of the best cars that you can drive in the densely populated and hilly terrain of San Francisco. Choose your car wisely to save on maintenance and fueling cost.

If you are only visiting San Francisco, Check out Lombard Street.

The Mulsanne, Bentley’s flagship sedan

Bentley is a British car manufacturer that has made a name for itself. In 2010, Bentley unveiled the Mulsanne as a new car model under the brand. That car has quickly become the top rated vehicle with the brand manufacturer. The Mulsanne is actually named for a notable curve in the Le Mans auto circuit. Bentley has taken notice of car drivers and their preferences for vehicles. BMW Specialist Repair Shop Chandler appreciate the features on this model.  Find out why it has become Bentley’s flagship sedan over the years.

The model is a full sized sedan and has all kinds of luxury features as well. View the interior and be captivated by the unique features on display too. It is clear that the Mulsanne was designed by visionaries for dedicated car drivers. All luxury vehicles come standard and should convince people to give it a try. Bentley’s flagship sedan is proving to be a big time success for all that are involved.

The vehicle also promises to offer both luxury and performance at once. The Mulsanne has a V-8 engine under the hood that clearly excels whenever possible. Initial tests have proven that the vehicle is a resounding success on the whole. Bentley’s flagship sedan is a leader in every sense of the word. The model can attain zero to sixty MPH in just 5.1 seconds on average. It has also passed safety testing and given people more confidence in its performance.

Expect a top speed of around 184 to 190 mph out on the road. Driving conditions may vary between the highway and city driving. There is between 505 and 530 horsepower under the hood. That is a good indication that the engine is high performance for serious drivers. People can test drive the Mulsanne at any local dealership when they want. The brand manufacturer has seen sales of the Mulsanne rise to a considerable extent. Bentley’s flagship sedan is more popular than ever before for those in the know. That helps drivers make a good decision for their favorite automobile. Trust the brand reputation when it comes to the vehicle.

Come to a Bentley dealership to see why the Mulsanne is so popular. It is a leading car and has sold well so far. The model has been in production since the 2011 model year. Bentley’s flagship sedan has seen a lot of interest from various drivers. There is ample seating inside of the car as well. Families could even make good use out of the vehicle whenever they need it most.

Rolls-Royce Ghost/Wraith – Silver Ghost of 1906

The new Rolls Royce- 40/50 hp chassis, for the first time it was launched at the popular London’s Olympia Motor show back in 1906. By the time, the Roll-Royce Ghost silver was the best car ever made in the world and was most luxurious car ever made with a very strong engine that we at www.newmansauto.com believe is still among the best engines you can get.

It was basically designed by Henry Royce with an objective of meeting the Edwardian Motorists demand a car that can carry the epitome of the most luxurious coachwork in the world.

The Roll Royce Silver Ghost was definitely one of the finest ever contemporary cars in the world. It was beloved of gentry landed as well as sporting gentlemen.

On the display, chassis were fitted with some elegant silver painted Roi-Des-Belges touring-coachwork as well as the silver plated brightwork by the coachbuilders Barker & Co. This car was primarily used as trial cars by Claude Johnson the company’s managing director. Claude Johnson Give it a new name as “The Silver Ghost”.

This wonderful vehicle had a six-cylinder engine as well as overdrive fourth speed. At this time, most motorists were unable to change the gear, but the Roll Royce was very adventurous. The silver ghost launched series of public test in 1907, thus culminating the observed 15,000-mile run.

Just within six weeks, John and another three driver’s team covered about 2,500 miles per week, running continuously around the clock, halting only when changing tires.

The trial of the Roll-Royce made a great impression on public motoring domain, thus named the Silver Ghost that was indiscriminately used to refer all Roll Royce 40/50s; thus making the company adopt the slogan, “The Best Car in the World”.

Regardless of whatever the speed it’s driven, there is no other engine that has that quality so far, one’s an auditory troubled nerve, standing or driving by the fuller sound than always emanate from the eight-day clock.

As earlier said this car was first revealed in 1906 and originated from the Manchester in the UK, it was a production car with a six-cylinder engine. The car was capable of running over 48 bhp. The car layout was front mounted-engine driving rear wheels. The car’s bodywork had various customarily made limousines and tourers.

The Roll Royce the silver ghost was able to run at a speed equivalent to 89 kph. The car still remains unique in its way due to the high-quality features it boasts.

Finally the 2013 Nissan GT-R Switzer R1K-X Red Katana

2013 Nissan GT-R Switzer

The 2013 Nissan GT-R Switzer R1K-X Red Katana ranks at tenth place on most powerful cars with the biggest engines, with a 3799cc displacement. It is among the first of R1KX GTRs series developed by Switzer Performance located in Ohio. The car has set a very good standard for the rest of its GT-R family. It comes with a VR38 Nissan engine that is custom-made, complete with reinforced pistons and rods. Its engine is very powerful, gunning down a speed of 400km/h and moving from 0 km/h to 100km/h within 2.5 seconds. At Auto Repair Pleasant Hill we find this impressive.

The 2013 Nissan GT-R Switzer R1K-X Red Katana has a beautiful sleek exterior with a two ton painting, often red in color that is well polished. It comes with a leather-lined interior cabin decorated with carbon fiber and Alcantara. Under the hood the beast runs on a 1400 horsepower. Its overall body weighs 1786kg, which is abit more that the standard GTRs owed to the added hardware equipment.

The car recently graced the Ohio Summit Motorsports Park and effortlessly run a 1/4 mile distance at an impressive speed of 163 miles per hour within 8.97 seconds. It has a monster internal cooling system, and SS90 exhaust system that keeps temperatures in check. Driving in it is a breeze. Installed in it is the high-performance premium audio system to meet your music needs.

The hardware for the 2013 Nissan GT-R Switzer R1K-X Red Katana was designed by a Switzer-tuned Syvecs standalone ECU, who allowed for the monster to deliver about 1250 horsepower from its engine to the wheels while maintaining the car’s interior comfort.

Finally the 2013 Nissan GT-R Switzer R1K-X Red Katana is worth in evry way. It is currently selling at around 270,000$ which is a bargain to the quality and specification it offers. It is a powerhouse that has set a high standard for all car manufacturers in the market.

The lesser known Bugatti – The 2016 Bugatti Chiron

2016 Bugatti Chiron

While we specialize in Check Engine Light Diagnosis we also have a passion for fast cars like the 2016 Bugatti Chiron which is a auto model that was composed by Giorgetto Giuaro and was outlined on a stage from the Lamborghini Diablo VT. The name of the auto, Chiron, is from an acclaimed Bugatti race driver named Louis Chiron. Being a model auto the 2016 Bugatti Chiron was the just a single since forever made.

The Chiron is an exceptionally streamlined auto as it has bends from heavily congested and has a low to the ground kind of body. The Chiron includes a back motor and the capacity trunk is in the front of the auto. The Chiron is a 2-seater roadster and the inside of the Chiron is unadulterated class as Bugatti utilized the finest materials like the best calfskin and wood. Inside the lodge of the Chiron there are two sorts of cowhide, which are Blu Pacifico (blue) and Sabbia (yellow.) The Chiron’s instrument board is developed of aluminum composite. The storage compartment in the front of the Chiron has an individual gear set that fits superbly in it.

The Chiron idea auto is developed of carbon fiber, which makes the auto exceptionally lightweight. The shade of the paint is Blue Cote d’Azur as it gives the auto an extremely energetic smooth look. The footing abilities on the Chiron are brilliant including a lasting 4-wheel drive and 20 inch wheels. The tires in the front are 265/30 and 335/30 in the back. The Chiron has a 3 organize naturally raised back spoiler that lessens the lift on the back hub giving the auto greatest footing. Since the Chiron is a low to the ground body outline and made up of lightweight carbon fiber and aluminum it permits the for extreme snappiness off the line while as yet having fantastic dealing with abilities.

The capable motor on the Chiron is a 18 chamber 6.3 liter that wrenches out 555 strength and quickens from 0-60 of every 5 seconds, hitting a greatest speed of 186 mph. The immediate infusion motor has an uprooting of 6.3 liters, a yield of energy of 408 kW, and a most extreme torque of 650 Newton meters. The motor in the Chiron is a similar motor that was utilized as a part of the EB118 and EB218 idea autos.

The guiding wheel in the Chiron is a little talked demonstrate, which is set before two vast dials and two littler dials on the focal passage, where there is a lever for the open entryway coupled to a 5-speed manual gearbox. There are four valves for each barrel in the 18 chamber Chiron so there is a sum of 72 valves. The pressure proportion is 11.5:1, the drag is 3.00 inches and the stroke is 2.98 inches.

The Bugatti EB 18-3 model looked on a par with it dealt with its unmistakable shading and tasteful plan of the inside. The execution abilities on this supercar are second to none as Bugatti made an exemplary with the Chiron that was first appeared at the 1999 Frankfurt International Motor Show.